MaxxECU modules - TuunerStuudio https://tuunerstuudio.ee/en/tootekategooria/juhtajud/maxxecu/maxxecu-moodulid/ Thu, 17 Jul 2025 11:16:00 +0000 en-US hourly 1 https://tuunerstuudio.ee/wp-content/uploads/2024/10/462539801_1749936732446472_7806435627202146352_n.png MaxxECU modules - TuunerStuudio https://tuunerstuudio.ee/en/tootekategooria/juhtajud/maxxecu/maxxecu-moodulid/ 32 32 VR to hall sensor converter (VR2DIN) board 2-channel DIY https://tuunerstuudio.ee/en/toode/vr-to-hall-anduri-konverter-vr2din-plaat-2-kanaliline-diy/ Sun, 01 Dec 2024 09:53:32 +0000 https://tuunerstuudio.ee/?post_type=product&p=20209 Simple dual channel VR to hall sensor converter module board.

Board to be soldered and wrapped in heat-shrink tube.
+5V power supply.br /> The VR to Hall Sensor converter provides a simple, cost-effective solution to connect a variable reluctance (VR) sensor to a hall effect sensor input on your MaxxECU. Simply connect +5V power, ground, and one (or two) VR sensors to the circuit board, and it will output a 5V DC square wave with a frequency that matches the AC signal created by the VR sensor.
Triggers at 0.4V, max 200V.

The post VR to hall sensor converter (VR2DIN) board 2-channel DIY appeared first on TuunerStuudio.

]]> The post VR to hall sensor converter (VR2DIN) board 2-channel DIY appeared first on TuunerStuudio.

]]> MaxxECU WBO module (including LSU 4.2 sensor) https://tuunerstuudio.ee/en/toode/maxxecu-wbo-moodul-kaasas-lsu-4-2-andur/ Sun, 01 Dec 2024 09:50:18 +0000 https://tuunerstuudio.ee/?post_type=product&p=20206 CAN module for MaxxECU to extend the number of Wideband sensors in the system, works on all MaxxECU units. Including connectors, Bosch LSU 4.2 sensor.

The post MaxxECU WBO module (including LSU 4.2 sensor) appeared first on TuunerStuudio.

]]> The post MaxxECU WBO module (including LSU 4.2 sensor) appeared first on TuunerStuudio.

]]> MaxxECU PWM module kit https://tuunerstuudio.ee/en/toode/maxxecu-pwm-mooduli-komplekt/ Sun, 01 Dec 2024 09:43:31 +0000 https://tuunerstuudio.ee/?post_type=product&p=20202 PWM module for variable control of pumps, fans, etc.

Connects to MaxxECU via CAN.
Primarily intended to control large fuel pumps.
By reducing the pump speed at low load, it's reducing power consumption, noise, and wear on the pump. It also reduces the heating of the fuel.
Can also control any other loads such as fans, hydraulic pump, etc.
Max load 60A (peak load such as fuel pumps)
50A max load for continuous loads like a fan.
Protected against overload and temperature.
Wiring harness, fuses, fuse holders and main relay included!

NOTE! Waterproof and can be mounted under the vehicle!

The post MaxxECU PWM module kit appeared first on TuunerStuudio.

]]> The post MaxxECU PWM module kit appeared first on TuunerStuudio.

]]> MaxxECU IGBT driver https://tuunerstuudio.ee/en/toode/maxxecu-igbt-juhtimismoodul/ Sun, 01 Dec 2024 09:38:48 +0000 https://tuunerstuudio.ee/?post_type=product&p=20199 Wires to MaxxECU IGN output, can be used as ignition amplifier, or to directly drive a NOS solenoid.
30A peak
10A nominal
REQUIRES to be mounted on a bigger surface to divert heat.

The post MaxxECU IGBT driver appeared first on TuunerStuudio.

]]> The post MaxxECU IGBT driver appeared first on TuunerStuudio.

]]> MaxxECU acceleration sensor (+/- 3G) https://tuunerstuudio.ee/en/toode/maxxecu-kiiruseandur-3g/ Sun, 01 Dec 2024 09:35:18 +0000 https://tuunerstuudio.ee/?post_type=product&p=20195 Acceleration sensor with the 0-5V output signal (max 3G)

  • Pin 1: Sensor GND
  • Pin 2: 0-5V output
  • Pin 3: +5V power supply

1V ut = -3G
2.5V = 0G
4V ut = 3G

Works with most ECU systems out there, but mainly developed for MaxxECU systems.

The post MaxxECU acceleration sensor (+/- 3G) appeared first on TuunerStuudio.

]]> The post MaxxECU acceleration sensor (+/- 3G) appeared first on TuunerStuudio.

]]> CANchecked MCE18 (V3) CAN input module https://tuunerstuudio.ee/en/toode/canchecked-mce18-v3-can-sisendi-moodul/ Sun, 01 Dec 2024 09:31:06 +0000 https://tuunerstuudio.ee/?post_type=product&p=20191 This module adds 9 analog, 9 digital inputs, and 3 low side outputs over CAN. Made in Germany by CANchecked.

  • 9st digitala inputs.
  • 9st analoga inputs (4st has optional built-in 1k1 pullup)
  • 3 digital outputs (on/off LOW SIDE 0.5A) (new in v2!)

Inputs are configured with the user CAN input functions.
New V3 hardware

The post CANchecked MCE18 (V3) CAN input module appeared first on TuunerStuudio.

]]> The post CANchecked MCE18 (V3) CAN input module appeared first on TuunerStuudio.

]]> BMW BSD communication board https://tuunerstuudio.ee/en/toode/bmw-bsd-kommunikatsiooniplaat/ Sun, 01 Dec 2024 09:26:56 +0000 https://tuunerstuudio.ee/?post_type=product&p=20188 The communication board needed to be able to communicate with the BMW BSD protocol

Supports the BMW BSD oil level sender and the alternator control. Must be wired to GPO 3 (GPO 7) and a regular GPO (GND)

The post BMW BSD communication board appeared first on TuunerStuudio.

]]> The post BMW BSD communication board appeared first on TuunerStuudio.

]]>